Physics Paper 1 Questions and Answers - Kapsabet Highschool Mock Exams 2022

Share via Whatsapp

Questions

INSTRUCTIONS

  • This paper consists of two sections A and B.
  • Answer all the questions in the spaces provided.
  • All workings must be clearly shown.
  • Mathematical tables and silent electronic calculators may be used.

SECTION A (25 MARKS)

  1. The figure below shows a micrometer screw gauge. What is the reading shown on the figure. (2 marks)
    KpsPhyP1q1
  2. State pressure law. (1 mark)
  3. State two factors that affect stability of a body. (2 marks)
  4. The diagram below shows a uniform wooden plank of length 4m and weight 10N. The plank is held at equilibrium by a weight of 40N placed at one end as shown below.
    KpsPhyP1q4
    Determine the distance d. (3 marks)
  5. Figure below shows a non-viscous fluid that is not compressible moving through a pipe of varied cross-sectional area.
    KpsPhyP1q5
    If the area of the narrow region is 0.05m2, calculate diameter of the wider region. (3 marks)
  6. State one use of thermal expansion. (1 mark)
  7. State two factors that affect melting point of a substance. (2 marks)
  8. A body is projected vertically upwards from the top of a building. If it lands on the base of the building. Sketch the velocity-time graph for motion. (2 marks)
  9. State a reason why transfer by radiation is faster than by conduction. (1 mark)
  10. The pulley system in the figure below supports a load of 50N.
    KpsPhyP1q10
    Given that the efficiency of the system is 80% calculate the effort, E. (3 marks)
  11. The figure below shows a glass container with cross-section area of 50cm2.
    KpsPhyP1q11
    When a wooden block of mass 120g is immersed into the water it floats while fully submerged and the water level rises by 4cm, determine the density of the water. (3 marks)
  12. Define the term momentum. (1 mark)
  13. What is a pitch of a screw. (1 mark)

SECTION B

  1. The figure below shows the motion of a trolley on ticker timer. The ticker has a frequency of 100Hz.
    KpsPhyP1q14
    1.        
      1. Calculate the initial velocity between A and B. (3 marks)
      2. Calculate the final velocity between C and D. (3 marks)
      3. Calculate the acceleration of the trolley during the motion. (3 marks)
    2. Figure below shows a force-distance graph for a car being towed on a level ground.
      KpsPhyP1q14b
      1. Calculate the total work done. (3 marks)
      2. If the velocity just before reaching point C is 0.6m/s. Calculate the power developed by the engine at this point. (2 marks)
  2.      
    1. A metal ball of mass 100g is dipped into boiling water at 1000C and then placed in a calorimeter containing 80g of water at 200C. After stirring, the temperature of the mixture stabilizes at 23.40C. Ignoring the heat gained by the calorimeter, determine the specific heat capacity of the metal. (Specific heat capacity of water = 4200j/Kg K). (4 marks)
    2. The cooling curve below is for a pure substance.
      KpsPhyP1q15b
      1. What is the melting point of the substance. (1 mark)
      2. State two factors that affect boiling point of a substance.
      3. At what part of the curve is the substance.
        Solid only?
        Liquid only?
        Solid and Liquid? (3 marks)
  3.              
    1. State Newton’s second law of linear motion. (1 mark)
    2. The legal speed limit on motorways is approximately 30m/s. In an incident on a motorway, a car of mass 900kg leaves a skid mark 75m long when stopping. The maximum deceleration of the car when skidding is approximately 10m/s2.
      1. Show that before the incidence, the car must have been travelling above the legal speed limit. (3 marks)
      2. Calculate for this skid, the maximum average braking force between each of the four tyres and the road. (3 marks)
      3. When the motorway is wet, the braking force provided by each wheel is reduced to 50% of the calculated in (ii) above. What is the effect of this reduced breaking force on stopping distance, explain your answer. Assume that the speed of the car before breaking is the same in both cases. (2 marks)
    3. A student carried out an experiment to measure static friction using identical wooden blocks arranged as shown in the figure.
      KpsPhyP1q16b
      State and explain which spring balance will indicate a smaller reading when the block just starts to move. (2 marks)
  4.    
    1. Give a reason why people experience nose bleeding when they climb tall mountains. (1 mark)
    2. The diagram shows a person raising a concrete block from a river bed by using two pulleys.
      KpsPhyP1q17d
      As shown in the diagram, the top of the block is 6.0m below the water surface. The density of water is 1000kg/m3 and the acceleration of free fall is 10m/s2. Calculate the water pressure acting on the top of the block. (3 marks)
    3. The block is raised through water. At one part, the water pressure acting on the top of the block 4.5 x 104 pa. The area of the top of the block is 0.015m2. Calculate the downward force exerted by the water on top of the block. (3 marks)
    4. When the block is clear of the water, it is raised a further 4.0m. The weight of the block is 550N. Calculate the work on the block as it is raised the 4.0m through air. (3 marks)
  5. The figure below shows part of an experiment set up to estimate the diameter of an oil molecule.
    KpsPhyP1q18
    1.      
      1. Describe how the oil patch is formed. (2 marks)
      2. What is the role of the Lycopodiumpowder. (1 mark)
    2. An oil drop of average diameter 0.7mm spreads out into a roughly circular patch of diameter 73.5cm on the surface of water in a trough.
      1. Calculate volume of the drop in mm3. Take (π = 22/7) (3 marks)
      2. Calculate the area of the patch in mm3. (2 marks)
      3. Calculate the thickness of the oil molecule and express your answer in standard form. (2 marks)

Marking Scheme

  1. Main scale reading 7.50mm
    Thimble scale 20 x 0.01 = 0.20
                            7.70mm
  2. State pressure law state that the pressure of a fixed mass of a gas is directly proportional to it’s absolute temperature provided volume is kept constant.
  3.        
    1. Position of the C.O.G.
    2. Base area of support
  4. Clock wise moment = anticlockwise moment
    40 x d = 10 (2 - d)
    40d = 20 - 10d
    40d + 10d = 20
    d = 20/50
    = 0.4m
  5. A1V1 = A2V2
    A1 x 0.1 = 2.2m/s x 0.05
    A1 = 2.2m/s x 0.05
    0.1
    = 1.1m2
  6. To measure temperature using a thermometer - mercury inside expands and contracts
  7.        
    • Pressure
    • Impurities
  8.       
    KpsPhyP1qa8
  9. Radiation does not require material medium for it to transfer heat. Conduction you need a material medium.
  10. V.R = 2
    80/100 = M.A/2
    M.A = 1.6
    M.A = L/E
    1.6 = 50/E⇒ E = 50/1.6
    E = 31.25N
  11. Density =     Mass     
                      Volume
            120g          
           50 x 4 cm3
    = 120g
    200cm3 = 0.6g/cm3
  12. Product of mass of a body and velocity (P = m x v)
  13. This is the distance between two successive threads of a screw.
  14.          
    1.        
      1. VAB = distance
                        time
        = 0.5/0.01s = 50m/s2
      2. VCD =    distance   
                      time
             5.0cm     = 500m/s2
              0.01s
      3. acceleration = v - u
           500m/s - 50m/s
                    5 x 0.02S
        = 4500m/s2
    2.    
      1. Work done = Area under the graph
        = (1/2 x 900J x 4m) + (900 x 4) + (1/2 x 900 x 4)
        = 1800J + 3600J + 1800J
        = 7200J
      2. Power = force x velocity
        = 900J x 0.6m/s
        = 540 Watts
  15.           
    1. Heat lost by the metal = heat gained by cold water
      0.1kg x C x (100 - 23.4)K = 0.8kg x 4200 x (23.4 - 20)K
      C =    0.8 x 4200 x (23.4 - 20)          
                    0.1 x (100 - 23.4)
      C = 1491.38JKg-1K-1
    2.      
      1. 800C
      2. Impurities
        Pressure
        Solid only - EF
        Liquid only - BC
        Solid and liquid - DE
  16.        
    1. The rate of change in momentum is directly proportional to the force causing it and it takes place in the direction of the force.
    2.              
      1. V2 = u2 + 2as
        V2 = 0 + 2 x 10 x 75
        V = 3.87m/s
      2. F = ma
        = 900 x 10
        = 9000J (total for four tires)
        Braking force for each tires = 9000J/4 =2250J
      3. The breaking distance will increase because wet road offers less frictional force which is required for breaking.
    3. Spring balance B rollers reduce friction between the surfaces.
  17.                   
    1. Atmospheric pressure decreases with altitude, pressure inside the body overcomes atmospheric pressure causing weak veins to burst.
    2. P = Pgh
      = 6 x 100 x 10
      = 600N/m2
    3. F = PxA
      0.015m2 x 4.5 x 10 pa
      = 675N
    4. Work done = Force x distance
      550N x 4M
      = 2200J
  18.     
    1.        
      1. When the oil is dropped on the water surface, it lowers it’s surface tension, this causes the powder to move away this forming a patch
      2. To make the oil patch visible
    2.      
      1. V = 4/3π0r3
        = 4/3 x 22/7 x (0.7/2)3
        = 4.19mm3
      2. Area = πr2
        (73.5/2)2 x 22/7
        = 1155mm2
      3. thickness (t) =      Volume of oil drop     
                                  Area of the patch
           4.19mm3
              1155mm2
        = 3.6 x 10-3mm 
Join our whatsapp group for latest updates

Download Physics Paper 1 Questions and Answers - Kapsabet Highschool Mock Exams 2022.


Tap Here to Download for 50/-




Why download?

  • ✔ To read offline at any time.
  • ✔ To Print at your convenience
  • ✔ Share Easily with Friends / Students


Get on WhatsApp Download as PDF
.
Subscribe now

access all the content at an affordable rate
or
Buy any individual paper or notes as a pdf via MPESA
and get it sent to you via WhatsApp

 

What does our community say about us?