- Conductors, Insulators and Semi-conductors
- Electronic Bond Structure
- Doping of Semi-conductors
- An insulator is a material or object which resists flow of heat (thermal insulator) or electrical charges (electrical insulators ). Examples are paraffin, wood, rubber, plastics etc.
- Conductors are materials that contain free electrons which carry an electrical charge from one point to another. Examples are metals and non-metals like carbon, graphite etc.
- Semi-conductors are materials or objects which allow the flow of electrical heat or energy through them under certain conditions i.e. temperature. Examples are germanium, silicon, cadmium sulphide, gallium arsenide etc.
- This is the series of allowed or forbidden bands that it contains according to the band theory which postulates the existence of continuous ranges of energy values (bands) which electron may occupy “allowed” or not occupy ‘forbidden”.
- According to molecular orbital theory, if several atoms are brought together in a molecule, their atomic orbitals split, producing a number of molecular orbitals proportional to the number of atoms.
- However when a large number of atoms are brought together the difference between their energy levels become very small, such that some intervals of energy contain no orbitals and this theory makes an assumption that these energy levels are as numerous as to be indistinct.
- Any solid has a large number of bands (theoretically infinite). Bands have different widths based upon the properties of the atomic orbitals from which they arise.
- Bands may also overlap to produce a bigger single band.
- Valence band is the highest range of electron energies where electrons are normally present at zero temperature.
- Conduction band is the range of electron energy higher than that of the valence band sufficient to make electrons free (delocalized) ; responsible for transfer of electric charge. Insulators and semi-conductors have a gap above valence band followed by conduction band above it.
- In metals, the conduction band is the valence band.
- Electrons in the conduction band break free of the covalent bonds between atoms and are free to move around hence conduct charge.
- The covalent bonds after the electrons have moved.
- The current carrying electrons in the conduction band are known as free electrons.
- Doping is the introduction of impurities in semi-conductors to alter their electronic properties.
- The impurities are called dopants.
- Doping heavily may increase their conductivity by a factor greater than a million.
- An intrinsic semi-conductor is one which is pure enough such that the impurities in it do not significantly affect its electrical behavior.
- Intrinsic semi-conductors increase their conductivity with increase in temperature unlike metals.An extrinsic semi-conductor is one which has been doped with impurities to modify its number and type of free charge carriers present.
- In this case the semi-conductor is given atoms by an impurity and this impurity is known as donor so it is given donor atoms (donated).
- The impurity within the semi-conductor accepts atoms with free electrons (dopants).
- This forms a ‘hole’ within-conductors.
- Junction refers the region where the two types of semi-conductors meet .
- The junctions are made by combining an n-type and p-type semi-conductor.
- The n-region is the cathode and the p-region is the anode.
Forward bias of a p-n junction
- It occurs when the p-type block is connected to the positive terminal and the n-type block is connected to the negative terminal of a battery.
- The depletion layer of the junction reduces to be very thin to allow the flow of electric current.
Reverse bias of a p-n junction
- The negative terminal of the battery is connected to the p-type region while the n-type is connected to positive terminal.
- The depletion layer widens and resists the flow of electrons to minimal or zero (no currentflowing through) when the electric field increases beyond critical point the diode junction eventually breaks down and at this voltage it is referred to as the breakdown voltage.
- Diodes are intended to operate below the breakdown voltage.
Applications of Junction Diodes
- They are mainly used for rectification of a.c. current for use by many electrical appliances.
Rectification is the conversion of sinusoidal waveform into unidirectional (non-zero) waveform.
Half Wave Rectification
- In this case the first half cycle of a sinusoidal waveform is positive and the inclusion of a reverse biased diode makes the current not to flow to the negative side of the wave.
- The current therefore conducts on every half cycle hence a half wave rectification is achieved.
- The voltage is d.c. and always positive in value though it is not steady and needs to be smoothed by placing a large capacitor in parallel to the load as shown.
Centre-tap Full Wave Rectification
- This is achieved by using a transformer whose output has a centre tap that is taken at two points where one is half the other as shown.
Bridge full Wave Rectification
- In this case a bridge rectifier is used to achieve a full wave rectification. The current flows in the same direction in both half cycles.
Radio Transmitter and Receiver
- Radio waves are produced by circuits that make electrons vibrate and they are known as oscillators which produce varied frequencies.
- Since radio waves have greater range in air than sound or even light waves they are used as carriers of audio (sound) and visual information (TV) waves.
- The sound is first changed into electrical vibrations by use of a microphone or other device then added to the radio carrier wave and this changes the amplitude of the carrier and is called amplitude modulation.
- The modulated wave is given out by the transmitting aerial and received by another aerial in a radio or TV when they cause vibrations between the earth and the aerial.
- They are then demodulated by a diode and hence heard as a sound or image.